PIC16C57C-04/SP【PDF 4/194 页】IC MCU OTP 2KX12 28DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3872

1页 2页 3页 [4页]5页 6页 7页 8页

PIC18F2450/4450

2006 Microchip Technology Inc.

Advance Information

DS39760A-page 99

9.0

I/O PORTS

Depending on the device selected and features

enabled, there are up to five ports available. Some pins

of the I/O ports are multiplexed with an alternate

function from the peripheral features on the device. In

general, when a peripheral is enabled, that pin may not

be used as a general purpose I/O pin.

Each port has three registers for its operation. These

registers are:

TRIS register (data direction register)

PORT register (reads the levels on the pins of the

device)

LAT register (output latch)

The Data Latch register (LATA) is useful for read-

modify-write operations on the value driven by the I/O

pins.

A simplified model of a generic I/O port, without the

interfaces to other peripherals, is shown in Figure 9-1.

FIGURE 9-1:

GENERIC I/O PORT

OPERATION

9.1

PORTA, TRISA and LATA Registers

PORTA is an 8-bit wide, bidirectional port. The

corresponding data direction register is TRISA. Setting

a TRISA bit (= 1) will make the corresponding PORTA

pin an input (i.e., put the corresponding output driver in

a high-impedance mode). Clearing a TRISA bit (= 0)

will make the corresponding PORTA pin an output (i.e.,

put the contents of the output latch on the selected pin).

Reading the PORTA register reads the status of the

pins; writing to it will write to the port latch.

The Data Latch register (LATA) is also memory

mapped. Read-modify-write operations on the LATA

PORTA.

The RA4 pin is multiplexed with the Timer0 module

clock input to become the RA4/T0CKI pin. The RA6 pin

is multiplexed with the main oscillator pin; it is enabled

as an oscillator or I/O pin by the selection of the main

oscillator

Configuration

(see

Section 18.1 “Configuration Bits” for details). When

not used as a port pin, RA6 and its associated TRIS

and LAT bits are read as ‘0’.

RA4 is also multiplexed with the USB module; it serves

as a receiver input from an external USB transceiver.

For details on configuration of the USB module, see

Section 14.2 “USB Status and Control”.

Several PORTA pins are multiplexed with analog inputs.

The operation of pins RA5 and RA3:RA0 as A/D

converter inputs is selected by clearing/setting the

control bits in the ADCON1 register (A/D Control

All other PORTA pins have TTL input levels and full

CMOS output drivers.

The TRISA register controls the direction of the RA

pins, even when they are being used as analog inputs.

The user must ensure the bits in the TRISA register are

maintained set when using them as analog inputs.

EXAMPLE 9-1:

INITIALIZING PORTA

Data

Bus

WR LAT

WR TRIS

RD PORT

Data Latch

TRIS Latch

RD TRIS

Input

Buffer

I/O pin(1)

RD LAT

or PORT

Note 1:

I/O pins have diode protection to VDD and VSS.

Note:

On a Power-on Reset, RA5 and RA3:RA0

are configured as analog inputs and read

as ‘0’. RA4 is configured as a digital input.

CLRF

PORTA

; Initialize PORTA by

; clearing output

; data latches

CLRF

LATA

; Alternate method

; to clear output

; data latches

MOVLW

0Fh

; Configure A/D

MOVWF

ADCON1

; for digital inputs

MOVLW

0CFh

; Value used to

; initialize data

; direction

MOVWF

TRISA

; Set RA<3:0> as inputs

; RA<5:4> as outputs

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式